ADK: D-5/922 EES: Electrical Energetic Systems Earthing and Grounding (IEEE 81 & IEC/EN 50522)

ADK: D-5/909 EEA: Electrical Energetic Automatic Trip-Out Ability and Safety (IEC/EN 60609-0 & IEC/EN 60947-2)

ADK: D-5/712 PVV: Photo Voltaic Installations Safety/Quality (SIST HD 60364-7-712)

ADK: D-5/919 PQA: Power Quality Analyzing & Reporting (SIST EN 50160 & IEEE 519)

Electrical safety of surrounding of power plants, transmission and distribution network, substations and industrial installations

Electrical Energetic Systems Earthing and Grounding (IEEE 81 & IEC/EN 50522): EES certification is focused on assuring of the safety conditions and protection against electrical shock by evaluating earthing, grounding and funnel potential rising based on IEEE 81, IEC 62305, EN 50522 and several other standards. Properly test and measuring methods used, compared and analysed with appropriate reporting can limit the risks as low as reasonably practicable. Ground integrity method, flex clamps method with hi current, hi frequency method, pulse method, use of earth analaysers, different testers & step / contact measuring systems are part of measuring methods and knowledge evaluation. Certified candidate is qualified to properly execute measurements and evaluate parameters, the limits suggested from the standards and results to PASS or FAIL barriers.

Electrical Energetic Automatic Trip-Out Ability and Safety (IEC/EN 60609-0 & IEC/EN 60947-2): EEA certification is focused on assuring of the safety conditions and protection against electrical shock by evaluating of automatic trip-out ability and trip-out time based on IEC 60909, IEC 60947-2, IEC 60364 and several other standards. Impedances, winding resistances, transformer ratio factors, tab changer testing, earth bonding and additional factors used in calculations to protect transformers and built-in equipment in case of overheating. Several procedures and measuring methods are explained for maintenance in safe manner when work energized. Certified candidate is qualified to evaluate parameters, the limits suggested from the standard and the examples of PASS or FAIL results. The responsibility of the candidate is to make correct reporting, marking, acting and informing appropriately.

Photo Voltaic Installations Safety/Quality (SIST HD 60364-7-712): PVV certification is focused on evaluating safety and quality of the photo-voltaic systems. The parameters of the panels and the strings, quality and degradation parameters, , measuring methods assuring of the safety conditions and protection against electrical shock, proper insulation evaluation of the system, evaluation of overcurrent and overvoltage protection, SPD protection, lightning protection and fire hazards, quality parameters on DC and AC side of invertor for efficiency of the system and much more. Certified candidate is qualified to evaluate parameters, the limits suggested from the standard and the examples of PASS or FAIL results. The responsibility of the candidate is to make correct reporting, marking, acting and informing appropriately.

Power Quality Analyzing & Reporting (SIST EN 50160 & IEEE 519): PQA certification is focused on assuring of the quality of the voltage, current and phase angle recording over standardized period of time, calculate hundreds of parameters according to IEEE 1448, IEEE 1459, IEEE 519, IEC 61000 series, EN 50160 and several other with reporting accordingly. Certified candidate is qualified to recognize faults and bad conditions as well as confirm good quality of the system. Use of Class A or Class S test equipment, recognize and select the proper type of equipment and accessories, evaluate the accuracy of results and PASS or FAIL barriers. The responsibility of the candidate is to make correct reporting, marking, acting and informing appropriately.

Initial and periodic inspection, verification, maintenance and responsibilities

Initial and periodic inspections for safety of electrical energetic systems and surrounding shall be performed at least each 5 years. Please check Facilities table for advice and compare the demand to local regulation. Only properly trained qualified personnel can perform work of the auditor assessment of electrical safety and quality.

Join the certification process and get the free copy of catalogues of knowledge to prepare yourself for certification easily.

Check Job Briefing and Planing for proper selection of certification needed.

Individual offer for companies and organisations

For your company or organization we can prepare an offer of training or preparation for the exam for an individual competence / qualification. Certification could be prepared in cooperation with employer where several restrictions and job evaluations need to be defined in advance. Application form document could help with employer – employee job briefing & planing for proper approach to energized or lockout tagout procedures.

Contact us and let us know your needs.